We have stumbled upon this great article involving Installing A Bathtub down the page on the net and felt it made good sense to discuss it with you on this site.
Installing a bathtub isn't exactly rocket science, but it does call for strong plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently obtainable, the job can move rapidly; if you have to open a wall to remove the old bathtub and also place the brand-new tub, the task is much harder. In either instance, the task is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub as well as set in the new one. See to it you have actually qualified yourself for the job and also fit attempting it. Rather than working with a professional to take over a halfway-completed project, it is far better to think about utilizing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This article will certainly assist you set up a new bath tub in your shower room if you have currently gotten a new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your tools as well as material list must comprise the following:
Getting ready for the Installment
First of all, the supporting structure supplied with the bathroom ought to be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the tap features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is detach the water system. After doing so, activate the faucets to drain any water staying in the system. The process of getting rid of the existing faucets can be fairly troublesome due to the restricted gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this procedure. Once the taps have been removed, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Before going on to fit the new faucets, contrast the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, position the bath tub in the required position. The wooden boards are useful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bath tub till the level checks out level.
To install faucets, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Activate the water as well as check all joints and brand-new pipework for leaks and tighten them if necessary. Load the tub and also examine the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has actually been made use of a minimum of once as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin ensuring that the washing machines remain in location in between the tap as well as the sink. Safeguard the tap in place with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal tap adapters. The previous type should be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a rigid seal, creating the water to penetrate the wall between the bathroom and also the tiling, leading to issues with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in usage. The sealant can fracture fairly early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the marketplace. It is advisable to fit the tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very involved in Installing A Bathtub and I'm hoping you appreciated the new entry. Sharing is nice. Who knows, you could be doing someone a favor. Thanks for your time. Visit again soon.
Request An Appointment